Current Affairs Quiz 2024GKCourses AptitudeADRE 2.0EnglishUGC NET

Production Engineering Quiz | Production Engineering Objective Type Questions & Answers

Download PDF

Free download in PDF Production Engineering Objective Type Questions & Answers for competitive exams. These short objective type questions with answers are very important for Board exams as well as competitive exams. These short solved questions or quizzes are provided by Gkseries.
Go To Download Page
(21) Sprue in casting refers to
[A] Vertical passage
[B] Riser
[C] Gate
[D] Runner
Answer: Vertical passage
(22) Which of the following operation is first performed?
[A] Boring
[B] Drilling
[C] Spot facing
[D] Tapping
Answer: Boring

DOWNLOAD CURRENT AFFAIRS PDF FROM APP

Article and Schedule Quiz Start Test!
(23) The casting defect caused by the erosion of sand
[A] Misrun
[B] Drop
[C] Wash
[D] Rat tail
Answer: Drop
(24) Ceramic cutting tools are
[A] Brittle and have low bending strength
[B] Available in the form of tips
[C] Made by cold pressing of aluminium oxide powder
[D] All of these
Answer: All of these
(25) Which of the following gating ratio represents pressurized gating systems?
[A] 1 : 1: 2
[B] 1 : 2 : 1
[C] 1 : 2 : 3
[D] 1 : 3 : 3
Answer: 1 : 2 : 1
(26) In a shaper, the length of stroke is increased by
[A] Increasing the centre distance of bull gear and crank pin
[B] Decreasing the centre distance of bull gear and crank pin
[C] Increasing the length of the arm
[D] Decreasing the length of the slot in the slotted lever
Answer: Increasing the centre distance of bull gear and crank pin
(27) Most commonly used materials cast by using hot-chamber die casting include
[A] Lead
[B] Tin
[C] Zinc
[D] All of these
Answer: All of these
(28) Spot facing is
[A] Localised machining of a component
[B] Machining of a spot to fit other parts
[C] Mahining of spol on the surface of a part to furnish a flat bearing or the head of a holt or nut
[D] A spot prepared on shaper or milling machine
Answer: Mahining of spol on the surface of a part to furnish a flat bearing or the head of a holt or nut
(29) A shim is
[A] A treatment given to a surface to prevent rusting
[B] A dull corner on a shaft
[C] A thin piece of sheet metal used between mating parts to provide the proper distance
[D] A surface on which bearings are fitted
Answer: A thin piece of sheet metal used between mating parts to provide the proper distance
(30) Quill is
[A] A tool used in milling machine to cut T-slots
[B] A holding device used on planers
[C] Curring a blind key way on an object
[D] A steel tube in the head of some machine tools that encloses the bearings and rotating spindle on which are mounted the cutting tools
Answer: A steel tube in the head of some machine tools that encloses the bearings and rotating spindle on which are mounted the cutting tools
31 Necking is
[A] Machining a groove around cylindrical shaft
[B] Drilling a hole in a plate
[C] Hole drilled for riveting
[D] Preparation of surface for brazing
Answer: Machining a groove around cylindrical shaft
32 Burr is
[A] Unmachined portion of work piece
[B] Boundary between finished and unifinished portion on a work piece
[C] A marking or work piece to identify for correct position on a work piece
[D] Sharp edge remaining on the metal after curring, stamping or machining
Answer: Sharp edge remaining on the metal after curring, stamping or machining
33 Buffing is
[A] A process of electroplating
[B] Covering a metal part with soft materials to prevent damage
[C] An finishing operation in broaching
[D] The process of bringing out the luster of metal
Answer: The process of bringing out the luster of metal
34 Angle plate is
[A] Used for holding angular jobs in milling machine.
[B] Used for cutting angles on jobs on shaper
[C] Cast iron jig used to hold work in a vertical position of layout or machining
[D] Used for measurement of angles
Answer: Used for measurement of angles
35 The size of a lathe is expressed by
[A] Gross weight of lathe
[B] Diameter of chuck
[C] Maximum speed of chuck
[D] Swing of lathe
Answer: Swing of lathe
36 Magna flux is
[A] A non-destructive inspection technique that makes use of magnetic field and magnetic particles to locate flaw in materials
[B] An instrument using ultrasonic techniques for crack detection
[C] An instrument used for inspection of weldings
[D] An instrument used for precision measurements using magnetism and flux density
Answer: A non-destructive inspection technique that makes use of magnetic field and magnetic particles to locate flaw in materials
37 A half nut is
[A] Damaged nut
[B] Nut manufactured in parts
[C] Nut with half the standard pitch
[D] Mechanism that locks the lathe carriage to the lead screw for thread cutting
Answer: Mechanism that locks the lathe carriage to the lead screw for thread cutting
38 Gang milling is
[A] Process of cutting gears
[B] Milling process for generating hexagonal surfaces
[C] Process in which two or more cutters are used simultangeously
[D] High speed milling
Answer: Process in which two or more cutters are used simultangeously
39 A flycutter is used on
[A] Lathe
[B] Shaper
[C] Milling machine
[D] Slotter
Answer: Milling machine
40 Lathe bed is made of
[A] Mild steel
[B] Cast steel
[C] Pig iron
[D] Close grain cast iron
Answer: Close grain cast iron

Take Mock Tests

Missiles Mock Test Start Test!
SSC MTS Mock Test Start Test
IBPS CLERK MOCK TEST Start Test
SSC MTS 2022 JULY 26 Shift 1 (ENGLISH) Start Test!
SSC GD Previous Year Paper 2021 Nov 17 Shift - I (Hindi) Start Test!
SSC CGL Tier - 1 PYP 2022 April 21 Shift- 1 (ENGLISH) Start Test!
MPSC PAPER I MOCK TEST 1 (ENGLISH) Start Test!
IB Security Assistant Mock test 1 (english) Start Test!
UP POLICE CONSTABLE MOCK TEST 1 Start Test!
DELHI POLICE CONSTABLE MOCK TEST 1 (HINDI) Start Test!
LEAVE A COMMENT