September 2023

A final examination is the______of a series of evaluations that a student has to go through

A final examination is the______of a series of evaluations that a student has to go through

Q. A final examination is the____________of a series of evaluations that a student has to go through. (A) culmination                          (B) consultation (C) desperation                          (D) insinuation Ans: culmination                        

A final examination is the______of a series of evaluations that a student has to go through Read More »

Once the team of analysts identify the problem, we______in a better position to comment on the issue

Once the team of analysts identify the problem, we______in a better position to comment on the issue

Q. Once the team of analysts identify the problem, we_______________in a better position to comment on the issue. Which one of the following choices CANNOT fill the given blank? (A) will be (B) were to be (C) are going to be (D) might be Ans: were to be

Once the team of analysts identify the problem, we______in a better position to comment on the issue Read More »

A project consists of six activities. The immediate predecessor of each activity and the estimated duration is also provided in the table below:

A project consists of six activities. The immediate predecessor of each activity and the estimated duration is also provided in the table below:

Q. A project consists of six activities. The immediate predecessor of each activity and the estimated duration is also provided in the table below: Activity Immediate predecessor Estimated duration (weeks) P – 5 Q – 1 R Q 2 S P, R 4 T P 6 U S, T 3 If all activities other than

A project consists of six activities. The immediate predecessor of each activity and the estimated duration is also provided in the table below: Read More »

Five jobs (J1, J2, J3, J4 and J5) need to be processed in a factory. Each job can be assigned to any of the five different machines (M1, M2, M3, M4 and M5)

Five jobs (J1, J2, J3, J4 and J5) need to be processed in a factory. Each job can be assigned to any of the five different machines (M1, M2, M3, M4 and M5)

Q. Five jobs (J1, J2, J3, J4 and J5) need to be processed in a factory. Each job can be assigned to any of the five different machines (M1, M2, M3, M4 and M5). The time durations taken (in minutes) by the machines for each of the jobs, are given in the table. However, each

Five jobs (J1, J2, J3, J4 and J5) need to be processed in a factory. Each job can be assigned to any of the five different machines (M1, M2, M3, M4 and M5) Read More »

Taylor’s tool life equation is given by VTn = C , where V is in m/min and T is in min. In a turning operation, two tools X and Y are used

Taylor’s tool life equation is given by VTn = C , where V is in m/min and T is in min. In a turning operation, two tools X and Y are used

Q. Taylor’s tool life equation is given by VTn = C , where V is in m/min and T is in min. In a turning operation, two tools X and Y are used. For tool X, n = 0.3 and C = 60 and for tool Y, n = 0.6 and C = 90. Both

Taylor’s tool life equation is given by VTn = C , where V is in m/min and T is in min. In a turning operation, two tools X and Y are used Read More »

In ASA system, the side cutting and end cutting edge angles of a sharp turning tool are 45° and 10°, respectively

In ASA system, the side cutting and end cutting edge angles of a sharp turning tool are 45° and 10°, respectively

Q. In ASA system, the side cutting and end cutting edge angles of a sharp turning tool are 45° and 10°, respectively. The feed during cylindrical turning is 0.1 mm/rev. The center line average surface roughness (in µm, round off to one decimal place) of the generated surface is   Ans: 3.75 Sol: Side cutting

In ASA system, the side cutting and end cutting edge angles of a sharp turning tool are 45° and 10°, respectively Read More »

A gas turbine with air as the working fluid has an isentropic efficiency of 0.70 when operating at a pressure ratio of 3

A gas turbine with air as the working fluid has an isentropic efficiency of 0.70 when operating at a pressure ratio of 3

Q. A gas turbine with air as the working fluid has an isentropic efficiency of 0.70 when operating at a pressure ratio of 3. Now, the pressure ratio of the turbine is increased to 5, while maintaining the same inlet conditions. Assume air as a perfect gas with specific heat ratio g = 1.4 .

A gas turbine with air as the working fluid has an isentropic efficiency of 0.70 when operating at a pressure ratio of 3 Read More »

A steam power cycle with regeneration as shown below on the T-s diagram employs a single open feedwater heater for efficiency improvement

A steam power cycle with regeneration as shown below on the T-s diagram employs a single open feedwater heater for efficiency improvement

Q. A steam power cycle with regeneration as shown below on the T-s diagram employs a single open feedwater heater for efficiency improvement. The fluids mix with each other in an open feedwater heater. The turbine is isentropic and the input (bleed) to the feedwater heater from the turbine is at state 2 as shown

A steam power cycle with regeneration as shown below on the T-s diagram employs a single open feedwater heater for efficiency improvement Read More »

If one mole of H2 gas occupies a rigid container with a capacity of 1000 litres and the temperature is raised from 27 oC to 37 oC, the change in pressure

If one mole of H2 gas occupies a rigid container with a capacity of 1000 litres and the temperature is raised from 27 oC to 37 oC, the change in pressure

Q. If one mole of H2 gas occupies a rigid container with a capacity of 1000 litres and the temperature is raised from 27 oC to 37 oC, the change in pressure of the contained gas (round off to two decimal places), assuming  ideal gas  behaviour, is___________Pa. (R=8.314 J/mol·K) Ans: 83.14 Sol: V=Volume of rigid

If one mole of H2 gas occupies a rigid container with a capacity of 1000 litres and the temperature is raised from 27 oC to 37 oC, the change in pressure Read More »

Three slabs are joined together as shown in the figure. There is no thermal contact resistance at the interfaces. The center slab experiences a non-uniform internal

Three slabs are joined together as shown in the figure. There is no thermal contact resistance at the interfaces. The center slab experiences a non-uniform internal

Q. Three slabs are joined together as shown in the figure. There is no thermal contact resistance at the interfaces. The center slab experiences a non-uniform internal heat generation with an average value equal to 10000 Wm−3, while the left and right slabs have no internal heat generation. All slabs have thickness equal to 1

Three slabs are joined together as shown in the figure. There is no thermal contact resistance at the interfaces. The center slab experiences a non-uniform internal Read More »