Q. Arrange the following processes in INCREASING magnitude of surface roughness of the casting. P. Investment casting Q. Permanent mould casting R. Pressure die casting S. Sand casting (A) R < S < Q < P (B) P < S < Q < R (C) R < P < Q < S (D) Q < […]
Q. Which of the following categories of materials is suitable as a filler for brazing of steel sheets? (A) Epoxy resins (B) Near-eutectic alloys (C) Refractory alloys (D) Large freezing range alloys Ans: Near-eutectic alloys
Q. Which of the following welding processes is NOT suitable for joining thin metal sheets? A. Gas Metal Arc Welding B. Electro Slag Welding C. Electron Beam Welding D. Laser Beam Welding Ans: Electro Slag Welding
Which of the following welding processes is NOT suitable for joining thin metal sheets? Read More »
Q. At equilibrium, the maximum number of phases in a three-component system at CONSTANT PRESSURE is: (A) 1 (B) 2 (C) 3 (D) 4 Ans: 4
At equilibrium, the maximum number of phases in a three-component system at Read More »
Q. During decarburization in a steel bath at 1550 oC, the compositions of dissolved C (wt.%C) and dissolved O (wt.%O) follow the relation: (wt.%C)(wt.%O) = K When the partial pressure of CO (𝑝𝐶𝑂) is 1 atm, K = 0.002. If 𝑝𝐶𝑂 = 0.1 atm, what is the value of K, at the same temperature? Note:
During decarburization in a steel bath at 1550 oC, the compositions of dissolved C Read More »
Q. Arrange the following in the correct sequence of operations in an integrated steel plant: i. Basic Oxygen Furnace (BOF) ii. Blast Furnace (BF) iii. Ruhrstahl Heraeus Degassing Process (RH) iv. Ladle Furnace Process (LF) (A) BOF→BF→LF→RH (B) BF→LF→BOF→RH (C) RH→LF→BF→BOF (D) BF→BOF→LF→RH Ans: BF→BOF→LF→RH
Arrange the following in the correct sequence of operations in an integrated steel plant Read More »
Q. In froth flotation, the primary purpose of adding collectors is to: A. make the surface of the mineral hydrophobic. B. make the surface of the mineral hydrophilic. C. stabilize the froth. D. adjust the pH. Ans: make the surface of the mineral hydrophobic.
In froth flotation, the primary purpose of adding collectors is to Read More »
Q. Analysis of a flow phenomenon in a system requires the following variables: i. Pressure [M L-1 T -2] ii. Velocity of the fluid [L T -1] iii. Size of the system [L] ivDensity of the fluid [M L-3] v. Viscosity of the fluid [M L-1 T -1] According to Buckingham Pi theorem (dimensional analysis)
Analysis of a flow phenomenon in a system requires the following variables Read More »
Q. What is the most-abundant anion in a 2CaO.SiO2 melt? (A) (SiO4) 4 – (B) (Si2O7) 6 – (C) (Si3O10) 8 – (D) (Si4O14) 10 – Ans: Option A
What is the most-abundant anion in a 2CaO.SiO2 melt? Read More »
Q. For a laminar flow of a liquid metal over a flat plate, the thicknesses of the velocity and thermal boundary layers are 𝛿𝑣 and 𝛿𝑡 respectively. Kinematic viscosity (viscosity/density) of liquid metal is significantly lower than its thermal diffusivity [thermal conductivity / (density × specific heat)]. Based on this information, pick the correct option.
