Q. The average velocity v of flow of clear water in a 100 cm (inner) diameter tube is measured using the ultrasonic flow meter as shown in the figure. The angle q is 45°. The measured transit times are t1 = 0.9950 ms and t2 = 1.0000 ms. The velocity v (in m/s) in the […]
Q. The inductance of a coil is measured using the bridge shown in the figure. Balance (D = 0) is obtained with C1 = 1 nF, R1 = 2.2 MΩ, R2 = 22.2 kΩ, R4 = 10 kΩ. The value of the inductance Lx (in mH) is Ans: 221 – 223
Q. A high Q coil having distributed (self) capacitance is tested with a Q-meter. First resonance at w1 = 106 rad/s is obtained with a capacitance of 990 pF. The second resonance at w2 = 2 ×106 rad/s is obtained with a 240 pF capacitance. The value of the inductance (in mH) of the coil
A high Q coil having distributed (self) capacitance is tested with a Q-meter Read More »
Q. The voltage and current drawn by a resistive load are measured with a 300 V voltmeter of accuracy ± 1% of full scale and a 5 A ammeter of accuracy ± 0.5% of full scale. The readings obtained are 200 V and 2.5 A. The limiting error (in %) in computing the load resistance
Q. The Boolean function 𝐹( 𝑋, 𝑌) realized by the given circuit is (A) 𝑋̅ 𝑌 + 𝑋 𝑌̅ (B) ̅𝑋 𝑌̅ + 𝑋 𝑌 (C) 𝑋 + 𝑌 (D) 𝑋̅ ∙ 𝑌̅ Ans: X̅ Y + X Y̅
The Boolean function 𝐹( 𝑋, 𝑌) realized by the given circuit is Read More »
Q. A 2-bit synchronous counter using two J-K flip flops is shown. The expressions for the inputs to the J-K flip flops are also shown in the figure. The output sequence of the counter starting from Q1Q2 = 00 is (A) 00 → 11 → 10 → 01 → 00 … (B) 00 → 01
Q. The product of sum expression of a Boolean function 𝐹(𝐴, 𝐵, 𝐶) of three variables is given by 𝐹(𝐴, 𝐵, 𝐶) = ( 𝐴 + 𝐵 + 𝐶̅ ) ∙ (𝐴 + 𝐵̅ + 𝐶̅) ∙ ( 𝐴̅ + 𝐵 + 𝐶 ) ∙ ( 𝐴̅ + 𝐵̅ + 𝐶̅ ) The canonical sum
Q. The circuit given uses ideal opamps. The current I (in mA) drawn from the source vs is (up to two decimal places) _ . Ans: 0.98 – 1
The circuit given uses ideal opamps. The current I (in mA) drawn from Read More »
Q. An opamp that is powered from a ± 5V supply is used to build a non-inverting amplifier having a gain of 15. The slew rate of the opamp is 0.5*106 V/s. For a sinusoidal input with amplitude of 0.3 V, the maximum frequency (in kHz) up to which it can be operated without any
An opamp that is powered from a ± 5V supply is used to build Read More »
Q. Unit step response of a linear time invariant (LTI) system is given by 𝑦(𝑡) = (1 − 𝑒−2𝑡)𝑢(𝑡). Assuming zero initial condition, the transfer function of the system is Ans: Option D
